Rifle Scopes & Rifle Stocks Just another WordPress site

There is no tax on a transfer to a lawful heir from the owner’s estate. Lawful heir just means someone named in a will to get the weapons, or a person entitled to inherit under the applicable intestacy laws if there was no will, or the will did not apply. The heir must be able to own the weapon under state and federal laws. The heir will have to do all the other steps of a transfer to an individual. Unless the heir is a class 3 he may not inherit post-86 machine guns (and would also need the police demo letter, see below). ATF is supposedly now allowing non licensed heirs to inherit pre-86 sample guns, a change from past policy. A weapon to an heir may also be transferred interstate, if need be; the gun need not be transferred to a dealer in the heir’s state, if the deceased owner resided in another state.

–

Millett 1-4X24 DSM Designated Marksman Rifle Scope

The Designated Marksman Scope fills the requirements of the law enforcement officer, rifle shooter, and the big game hunter who needs a quick-sighting system at ranges of 5 yards to 500 yards. The Dot-in-a-Donut reticle allows for fast, natural aiming. The shooter’s eye lines up the circle at close range, and the one MOA (Minute of Angle) dot gives accuracy at the longer ranges. Range estimation is straight forward by use of the circle out to 500 yards. Compact design, 30mm tube, fully coated glass and bright illumination of the reticle are just a few of the many features of the DMS-1. Bright red illumination of the reticle adds to the quickness of the sighting system in day and low-light conditions. At 1 power it works well as a reflex sight and at longer ranges the 4X magnification gives increased accuracy.

Millett 1-4X24 DSM Designated Marksman Rifle Scope width=500 height=231>

DMS-1 is a concept that is long overdue. This compact, fast CQB to mid-range scope takes the best of scope-type optics and red dot reflex sights and puts it all together. A Dot-in-a- Donut is the best way to describe the DMS reticle. At close ranges, just put the donut on the target and pull the trigger. At longer ranges, you have the 1 MOA (Minute of Angle) dot in the center of the donut to give you superior accuracy. As all the measurements are standard MOA (Minute of Angle), you can use the reticle for range finding and hold over. True 1X with both eyes open for close and quick sighting, and 4X for accuracy at the longer ranges. Works equally well on tactical ar15 accessories weapons or big game rifles. Great for hunting dangerous game, as you have the ability to make that quick shot and hit your target while the pressure is on. Fully multi-coated lenses and rugged one-piece tube are featured. The DMS is also an excellent choice for large, fast moving, dangerous game. Try the DMS and you will see the advantage.

ATF has created interim rules to implement PL 103-322, and they are a little more specific, and a little more onerous:

–

Test of DukeALERT emergency system a success
Nearly 61,700 e-mail alerts and 4,639 text messages delivered to students, faculty, staff and neighbors

Harris Bipods for the AR-15 » AR-15 Bipods
Harris Bipods for the AR-15

CAMOUFLAGE for hunting and ghillie suits
Pistol Grip. The telescoping stocks are available in either an aluminum or plastic construction, both of which are strong enough for the purpose, but the aluminum have a tendency …

Ruger 10/22 Gun Accessories
Mini 14 gun accessory review

Harris Bipods for the AR-15
Harris Bipods for the AR-15

18 USC sec. 921(a)(24) “The term ‘firearm silencer’ or ‘firearm muffler’ means any device for silencing, muffling, or diminishing the report of a portable firearm, including any combination of parts, designed or redesigned, and intended for use in assembling or fabricating a firearm silencer or firearm muffler, and any part intended only for use in such assembly or fabrication.”

–

Rifle Scopes
Just another WordPress weblog … The Fall of My Leftist House mirrors Calderon’s Call (AR-15 ACCESSORIES)

The definition of “machinegun” in the NFA (26 USC sec. 5845(b)) includes parts to convert a gun into a machine gun. Note that conversion parts are not included in the definition of “firearm” under the Gun Control Act, one of the few things I know of that is a firearm under the NFA, but not the GCA. Thus the purchaser of a conversion part from an FFL need not do a 4473 form, unlike other NFA weapons. Of course the host gun, if purchased from an FFL, will require the 4473. This reading of the law is based on numerous statements from ATF, and the definition of “firearm” under the GCA, which requires it be able to expel a shot. However, at least one very slow judge has decided that somehow the definition of “firearm” in the GCA “incorporates” the definition of “machine gun” under the GCA (even though the law doesn’t say that) and that a machine gun conversion part is a “firearm” under the GCA as well as the NFA. I think the judge is clearly wrong, even ATF reads the law better than that, but the point is to be careful. The case is U.S. v. Hunter, 843 F.Supp 235 (E.D. Mich. 1994), and see also the same judge’s second opinion in the same case, at 863 F.Supp. 462 (E.D. Mich. 1994). These parts are called registered sears, as well as other parts or sets of parts to convert a gun into a machine gun.

–

To get Calif laws, pending bills and other stuff ftp to ftp.sen.ca.gov or ftp to leginfo.public.ca.gov, and look in /pub/code /pub/code/pen has the penal code.

On top of the FOPA machine gun restrictions, any NFA weapon imported into the US after the Gun Control Act took effect (end of 1968) cannot be transferred to an individual. See 26 USC sec. 5844. They can be transferred to SOT’s, without any police demonstration request, and kept by the SOT after surrendering his SOT. These are sometimes called “pre-86 samples”, or “dealer samples”, although dealer sample can be used to refer to either a post-86 machine gun or any NFA weapon imported after 1968.

–

A.R.M.S. #22M68 Aimpoint Comp Throw Lever Scope Ring

Aimpoint Throw Lever Ring – 30mm – Designed exclusively for the Aimpoint Comp. The A.R.M.S. unique ring saddle allows for optimum surface contact for the most secure fit. Ultra rugged and low mounting that can also be modularly raised via optional spacer platforms. The spacers can be added at a modest cost. Secured to an A.R.M.S. #17 Platform with the A.R.M.S. patented Throw Lever system guarantees easy on and off repeat zero. Built in no mar patented buffer pad. This unit now fits both the model ML2 and M2 variations of the Aimpoint Comp. Sight. This mount will also accommodate the new Trijicon Tri-Power Sight. 22M68Spacers also available for added height.

Table of Contents

–

Weaver scope mount Aluminum Bases for Marlin 39A (Round Barrel)

One Piece top mount base used on:

• Marlin 39A (Round Barrel) – Rear base is positioned on top of receiver and front base is positioned on the barrel. Drilling & tapping required. One-piece base mounts w/2 set screws & newer guns are factory drilled & tapped.

Weaver Models

• Weaver 48090:WeaverBase,Top Mount 90
  
  Posted in Nightforce Scopes by admin. No Comments